View FTLF1519P1XNL_8502065.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product specification 2 gb/s rohs compliant long - wavelength pluggable sfp transceiver ftlf 1519p1xnl product features ? up to 2.125gb/s bi - directional data links ? hot - pluggable sfp footprint ? built - in digital diagnostic functions ? uncooled 1550nm dfb laser t ransmitter ? duplex lc connector ? rohs compliant and lead free ? metal enclosure, for lower emi ? single 3.3v power supply ? up to 80 km on 9/125 m smf ? low power dissipation typically <700mw ? extended operating temperature range: - 5c to 85 c applications ? gi gabit ethernet ? 1x and 2x fibre channel finisar?s ftlf1519p1xn l small form factor pluggable (sfp) transceivers are compatible with the small form factor pluggable multi - sourcing agreement (msa) 1 . they simultaneously comply with gigabit ethernet as specifi ed in ieee std 802.3 2 , and 1x and 2x fibre channel as defined in fc - pi 13.0 3,4 . the optical transceiver s are compliant per the rohs directive 2011/65/eu. see finisar application note an - 2038 for more details. digital diagnostics functions are available via the 2 - wire serial bus spe cified in the sfp msa. product selection ftlf 1519p1xnl x w wide extraction bail b narrow extraction bail ? finisar corporation j uly 2015 rev b page 1
ftlf 1519p1xnl pluggable sfp product specification i. pin descriptions pin symbol name/description ref. 1 v eet transmitter ground (common with receiver ground) 1 2 t fault transmitter faul t. not supported. 3 t dis transmitter disable. laser output disabled on high or open. 2 4 mod_def(2) module definition 2. data line for serial id. 3 5 mod_def(1) module definition 1. clock line for serial id. 3 6 mod_def(0) module definition 0. grounde d within the module. 3 7 rate select no connection required 4 8 los loss of signal indication. logic 0 indicates normal operation. 5 9 v eer receiver ground (common with transmitter ground) 1 10 v eer receiver ground (common with transmitter ground) 1 11 v eer receiver ground (common with transmitter ground) 1 12 rd - receiver inverted data out. ac coupled 13 rd+ receiver non - inverted data out. ac coupled 14 v eer receiver ground (common with transmitter ground) 1 15 v ccr receiver power supply 16 v cct transmitter power supply 17 v eet transmitter ground (common with receiver ground) 1 18 td+ transmitter non - inverted data in . ac coupled. 19 td - transmitter inverted data in. ac coupled. 20 v eet transmitter ground (common with receive r ground) 1 notes : 1. circuit ground is internally isolated from chassis ground. 2. laser output disabled on t dis >2.0v or open, enabled on t dis <0.8v. 3. should be pulled up with 4.7k - 10 kohms on host board to a voltage between 2.0v and 3.6v. mod_def(0) pulls line low to indicate module is plugged in. 4. finisar ftlf xx19xxxxx transceivers operate at 1x and 2x fibre channel, and gigabit ethernet data rates and respective protocols without active control. 5. los is open collector output. should be pulled up with 4.7k ? 10 kohms on host board to a voltage between 2.0v and 3.6v. logic 0 indicates normal operation; logic 1 indicates loss of signal. veet veet veer veer td- td+ rd+ rd- vcct vccr veet veer txfault mod-def(2) mod-def(1) mod-def(0) rate select los 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 towards asic towards bezel tx disable veer pinout of connector block on host board ? finisar corporation j uly 2015 rev b page 2
ftlf 1519p1xn l pluggable sfp product specification ii. absolute maximum ratings parameter symbol min typ max unit ref. maximum supply voltage vcc - 0.5 4.5 v storage temperature t s - 40 85 c case operating temperature t op - 5 85 c relative humidity rh 0 85 % 1 iii. electrical characteristics (t op = - 5 to 85 parameter symbol min typ max unit ref. supply voltage vcc 3.15 3.60 v supply current icc 200 300 ma transmitter ? receiver ? ? non condensing. 2. connected directly to tx data input pins. ac coupled thereafter. 3. or open circuit. 4. into 100 ohms differential termination. 5. 20 ? 80 % 6. loss of signal is lvttl. logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. receiver sensitivity is compliant with power supply sinusoidal modulation of 20 hz to 1.5 mhz up to specified value applied through the recommended power supply filtering network. valid on receive side for input powers within receive sensitivity. 8. measured with dj - free data input signal. in actual application, output dj will be the sum of input dj and ? ? finisar corporation j uly 2015 rev b page 3
ftlf 1519p1xn l pluggable sfp product specification iv. optical charac teristics (t op = - 5 to 85 parameter symbol min typ max unit ref. transmitter ? ? receiver class 1 laser safety per fda/cdrh and en (iec) 60825 regulations. 2. meets curves in fc - pi 13.0 figures 18 and 19, which allow trade - off bet ween wavelength, spectral width and oma. 3. equivalent extinction ratio specification for fibre channel. allows smaller er at higher average power. 4. unfiltered, 20 - 80%. complies with ieee 802.3 (gig. e), fc 1x and 2x eye masks when filtered. 5. measured with dj - f ree data input signal. in actual application, output dj will be the sum of input dj and ? measured with conformance signals defined in fc - pi 13.0 specifications. 7. measured with prbs 2 7 - 1 at 10 -12 ber ? finisar corporation j uly 2015 rev b page 4
ftlf 1519p1xn l pluggable sfp product specification v. genera l specifications parameter symbol min typ max units ref. data rate br 1062 2125 mb/sec 1 bit error rate ber 10 - 12 2 max. supported link length on 9/125 m smf @ 2x fibre channel l max1 76 km 3, 4 max. supported link length on 9/125 gigabit ethernet and 1x/2x fibre channel compliant . 2. tested with a prbs 2 7 - 1 test pattern. 3. dispersion limited per fc - pi rev. 13 4. attenuation of 0.25 db/km is used for the link length calculations. distances are indicat ive only and are calculated solely on link budget. a 2db penalty is included for dispersion on >2gb/s data rates. please refer to the optical specifications in table iv to calculate a more accurate link budget based on specific conditions in your applic ation. vi. environmental specifications finisar 1550nm sfp transceivers have an extended operating temperature range from ? 5c to +85c case temperature. parameter symbol min typ max units ref. case operating temperature t op - 5 85 c storage temp erature t sto - 40 85 c vii. regulatory compliance finisar transceivers are class 1 laser products and comply with us fda regulations. these products are certified by tv and csa to meet the class 1 eye safety requirements of en (iec) 60825 and the electrical safety requirements of en (iec) 60950. copies of certificates are available at finisar corporation upon request. copies of the referenced certificates are available at finisar corporation upon request. ? finisar corporation j uly 2015 rev b page 5
ftlf 1519p1xn l pluggable sfp product specification viii. digital diagnostic functions f inisar ftlf 1519p1xnl sfp transceivers support the 2 - wire serial communication protocol as defined in the sfp msa 1 . it is very closely related to the e 2 prom defined in the gbic standard, with the same electrical specifications. the standard sfp serial id p rovides access to identification information that describes the transceiver?s capabilities, standard interfaces, manufacturer, and other information. additionally, finisar sfp transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real - time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. it also defines a sophisticated system of alarm and warnin g flags, which alerts end - users when particular operating parameters are outside of a factory set normal range. the sfp msa defines a 256 - byte memory map in e 2 prom that is accessible over a 2- wire serial interface at the 8 bit address 1010000x (a0h). the digital diagnostic monitoring interface makes use of the 8 bit address 1010001x (a2h), so the originally defined serial id memory map remains unchanged. the interface is identical to, and is thus fully backward compatible with both the gbic specification and the sfp multi source agreement. the complete interface is described in finisar application note an - 2030: ?digital diagnostics monitoring interface for sfp optical transceivers?. the operating and diagnostics information is monitored and reported by a digital diagnostics transceiver controller (ddtc) inside the transceiver, which is accessed through a 2 - wire serial interface. when the serial protocol is activated, the serial clock signal (scl, mod def 1) is generated by the host. the positive edge cloc ks data into the sfp transceiver into those segments of the e 2 prom that are not write - protected. the negative edge clocks data from the sfp transceiver. the serial data signal (sda, mod def 2) is bi - directional for serial data transfer. the host uses sda in conjunction with scl to mark the start and end of serial protocol activation. the memories are organized as a series of 8 - bit data words that can be addressed individually or sequentially. for more information, please see the sfp msa documentation 1 or finisar application note an - 2030. digital diagnostics for the ftlf 1519p1xnl are externally calibrated by default. please note that evaluation board fdb - 1018 is available with finisar moddemo software that allows simple to use communication over the 2 - wi re serial interface. ? finisar corporation j uly 2015 rev b page 6
ftlf 1519p1xn l pluggable sfp product specification ix. mechanical specifications finisar?s FTLF1519P1XNL small form factor pluggable (sfp) transceivers are compatible with the dimensions defined by the sfp multi - sourcing agreement (msa). ftlf 1519p1bnl ? finisar corporation j uly 2015 rev b page 7
ftlf 1519p1xn l pluggable sfp product specification ftlf 1519p1wnl ? finisar corporation j uly 2015 rev b page 8
ftlf 1519p1xn l pluggable sfp product specification x. pcb layout and bezel recommendations ? finisar corporation j uly 2015 rev b page 9
ftlf 1519p1xn l pluggable sfp product specification ? finisar corporation j uly 2015 rev b page 10
ftlf 1519p1xn l pluggable sfp product specification xi. references 1. small form factor pluggable (sfp) transceiver multi - source agreement (msa), september 2000. documentation is currently available at finisar upon request. 2. ieee std 80 2.3. ieee standards department, 2002. 3. ?fibre channel draft physical interface specification (fc - pi 13.0)?. american national standard for information systems.(*) 4. ?fibre channel physical and signaling interface (fc - ph, fc - ph2, fc - ph3)?. american national standard for information systems. 5. directive 2011/65/eu of the european council parliament and of the council, ?on the restriction of the use of certain hazardous substances in electrical and electronic equipment?. certain products may use one or m ore exemptions as allowed by the directive. 6. ?application note a n - 2038: finisar implementation o f rohs compliant transceivers? (*) fc - pi 13.0 does not specify a 1550nm dfb interface for extended reach applications. the ftlf1519p1xcl complies with this standard, except for the optical output power. see section iv for details. xii. for more information finisar corporation 1389 moffett park drive sunnyvale, ca 94089 - 1133 tel. 1 - 408- 548- 1000 fax 1 - 408- 541- 6138 sales@finisar.com www.finisar.com ? finisar corporation j uly 2015 rev b page 11

▲Up To Search▲

Price & Availability of FTLF1519P1XNL

	To Download FTLF1519P1XNL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .